Legs for the workbench...

It's been a while since I've updated this thing. We've been converting a dining room into an office, and fixing up the house some. So there's not been time for woodwork. I do have some news, though. The gentleman at the sawmill left me a voice mail and told me he had the walnut cut up for the legs of my workbench. It's currently in the kiln. So in a few weeks, I'll be able to take my workbench off of those saw horses and get it on a more stable surface. Finally.

Forcast looks good...

So far, the forecast for this weekend looks good for woodworking. The highs are supposed to be in the mid 50s. I hope I'll finally be able to get the stain on the inside pieces of the cabinet. If not, I can at least work on the legs and base some more. I may have to go to the local lumber guy and pick up some clear poplar for the legs. I have about 30 bdft, but it's knotted pretty good and I would like clear legs at least.

Not only that, I can check on the legs for my workbench. He never called to tell me the walnut was done. Maybe he just hasn't gotten to it yet, but we'll see tomorrow.

Got halfway through...

I only got to read half of "Workbenches". It is very well written, and very informative. Schwarz's writing is like listening to a friend describing his experiences with workbenches. Schwarz states upfront that this book is different from the other workbench books, and he is right! Schwarz tells you what he likes, and doesn't like about all aspects of a workbench. The man should know, I believe he stated he as built 10 over the years. I couldn't imagine. It's taken me a year to build 1!

The Workbenches book....

just arrived at my desk. It's got a huge dent in the side of it. Thanks USPS, you suck. I didn't realize it was hardcover. It's a very nice book, autographed even. I'm firing up the included CD-Rom right now. I'll report back later on it. It'll be difficult to get work done today with this book at my desk. I'll probably have the whole thing read by tonight.

Just ordered Christopher Schwarz's book...

I have both of the "workbench" books. When I saw that Christopher Schwarz wrote a book on workbenches I knew I had to get it. I could have bought it off Amazon, or even Barnes & Noble for almost $10 cheaper. Instead I bought it off of Christopher's site, for two reasons. Firts, it comes with a CD that contains the book and drawings. Second, it's autographed.

If you've never checked out Christopher's blog, I have it in my Links section. I recommend checking it out.

... the search continues.

I found some walnut for the legs. 16/4 hit or miss. I found enough to make the legs. Unfortunately, it was $9.90 bft. WHOA! I know walnut comes at a premium... $9.90 bft for S2S hit or miss!? I figure I want about 27 bft. So, $9.90 x 27 = $267.3, before tax! I'm going to try to start calling some lumber yards in Nashville. I've went there before for lumber, so maybe I can get lucky again.

Powered by ScribeFire.

All your base...

I've been scouring a radius of 90 miles trying to find wood for the base of this thing. I'm want maple, poplar or hickory. The thing is I can hardly find rough lumber big enough to get a 4"x4"x42" dimensioned piece. Let me retract that statement. I've found both hard maple and poplar that would do, but I ain't paying almost $250 for it. Only one local distributor has it and they charge a premium. The search continues.

Ends leveled...

I have leveled off the ends of the bench, and patched a terrible piece of tearout. But that's a post when I feel like reliving the experience. No pics yet. I'll try to post some soon.

Ready to level the ends...

Well, here it is. Sorry for the horrible picture but I was in a hurry. I had a pic I annotated for a friend, so I thought I'd share it here.

Time to glue up!

I applied glue to the plywood spline and the mortises and clamped them up. You can see that I didn't have pipe long enough for my pipe clamps. Fortunately, I did have 6 clamps. This is what I like to call "creative problem solving". You can use that on a resume, I did.

Dry fit...

Here's a pic of a dry fit of one end. It took forever to mortise out the end of the bench. I know there's a couple of marks left on the end, that's ok. The end is flat, and anyway that surface isn't a structural surface for glue (endgrain).

Mortis'...

I need to cut the mortise for the spline of the breadboard end. The end on the left was cut first with my router. I didn't like the way it came out, so I decide to cut the mortise on the other by hand. Unfortunately, I do not have a mortising chisel. I used my Irwin/Blue Marples paring chisels to cut the mortise on the right. The dimensions of the mortise on the left is 13/16" w x 18"l x 3/4" d. The mortise on the right is 13/16" x 4" x 1/2"d. Notice the difference in dimensions there? Yeah, took me 30 minutes to do the mortise on the right. I broke the Colt back out to finish it up. Well worth it.

Now it's time to square up the ends. Well... mostly square, cause I'm not perfecct. Yet. The bench at this point weighs at least 100 lbs. I tried cutting the ends by hand, but I made a real mess of one of the ends. Fortunately, I had left plenty of material for mistakes.
1. I setup two rollers on the right side of the blade with 2 2x4s. One 6' and one 8'.
2. I made a simple outfeed table out of a sawhorse to support the top at the end of the cut.
3. I screwed a piece of maple that fit in the t-slot to the underside of the bench top. I recovered the maple strip from a failed cross-cut sled.
4. I sawed away.

You can see from the burn marks that I had a difficult time on the first end. The maple did a pretty good job of holding the top straight but I didn't do a good job of pushing. The second end came out almost free of marks.

Did I mention that thing was heavy?

Ready for the ends...

So, now I'm ready to put on the breadboard ends. Why breadboard? Well... the maple pieces are face glued. So, if I just glued the walnut ends on it would be an end grain (maple) to long grain (walnut) butt joint. If you're a new woodworker, this is a big no-no. So, I'm going with breadboard end. If you need more information on breadboard ends... goto any of the woodworking forums and do a search in the archives. I promise you someone has already explained what they are, the benefits, and detriments of their use.

almost... flat....

I tried flattening this bad boy... man oh man... not done yet. I got the middle and the ends flat across the bench, but the length of the bench is way more difficult.

I need to buy or create some winding sticks so I can make sure it's not twisted.

Flattening...

Here's the tools used for flattening. I got it fairly flat. Not perfect. I plan on using the #80 scraper to get it flatter.

Trim time...

I added the walnut trim. I cut it pretty much the same way I did the maple. Glued it up the same too. I then hand planed it flat with the maple.

Flat... almost

I got it as close as I want before I add the trim. Here's a pic.

Top ready to flatten...

The clamps come off! There's a lot of glue squeeze out, which I think is

good. I started in with the scrub plane and worked my way up to a #80 cabinet scraper. My triceps are now the size of Hulk Hogan's.

In hindsight I wish I had put a clamping caul across the top of the sections to keep the boards aligned vertically. Of course, I was using all the jigs I had, so I plane.

Lost pics... top glued up

Unfortunately, I lost the pictures for the glue-up process. But here it is anyway.

1. Milled the lumber to 3/4" x 3" x 66".
   
2. Drilled 3, 1/2" holes in each board. 2" from each end then in the middle.
3. I only glued up 4 boards at a time using the all-thread as a makeshift clamp and some Erwin quick clamps.
4. The last group of boards I glued up 3 of the boards and then routed the dog holes on the other two. More on this later.
5. I put all the sections together using the all-thread bars and pipe clamps.